×
![]()
ATV12HU22M2
درایو 2.2 کیلووات، تکفاز سری ATV12
variable speed drive ATV12 - 2.2kW - 3hp - 200..240V - 1ph - with heat sink
مشخصات کامل
product destination
Asynchronous motors
product destination
component name
ATV12
component name
built-in fan
With
built-in fan
network number of phases
1 phase
network number of phases
motor power kW
2.2 kW
motor power kW
motor power hp
3 hp
motor power hp
line current
24 A at 200 V
20.2 A at 240 V
line current
speed range
1…20
speed range
IP degree of protection
IP20 without blanking plate on upper part
IP degree of protection
سری
Altivar 12
range of product
product or component type
Variable speed drive
product or component type
product specific application
Simple machine
product specific application
communication port protocol
Modbus
communication port protocol
[Us] rated supply voltage
200...240 V - 15...10 %
[Us] rated supply voltage
EMC filter
Integrated
EMC filter
supply frequency
50/60 Hz +/- 5 %
supply frequency
connector type
1 RJ45 (on front face) for Modbus
connector type
physical interface
2-wire RS 485 for Modbus
physical interface
transmission frame
RTU for Modbus
transmission frame
transmission rate
4800 bit/s
9600 bit/s
19200 bit/s
38400 bit/s
transmission rate
number of addresses
1…247 for Modbus
number of addresses
communication service
Read holding registers (03) 29 words
Write single register (06) 29 words
Write multiple registers (16) 27 words
Read/write multiple registers (23) 4/4 words
Read device identification (43)
communication service
continuous output current
10 A at 4 kHz
continuous output current
maximum transient current
15 A for 60 s
maximum transient current
speed drive output frequency
0.5…400 Hz
speed drive output frequency
braking torque
Up to 70 % of nominal motor torque without braking resistor
braking torque
output voltage
200...240 V 3 phases
output voltage
electrical connection
Terminal, clamping capacity: 5.5 mm², AWG 10 (L1, L2, L3, U, V, W, PA, PC)
electrical connection
tightening torque
1.2 N.m
tightening torque
insulation
Electrical between power and control
insulation
supply
Internal for reference potentiometer: 5 V DC (4.75…5.25 V), <10 mA, protection type: overload and short-circuit protection
Internal for logic inputs: 24 V DC (20.4…28.8 V), <100 mA, protection type: overload and short-circuit protection
supply
analogue input type
Configurable current AI1 0...20 mA 250 Ohm
Configurable voltage AI1 0...10 V 30 kOhm
Configurable voltage AI1 0...5 V 30 kOhm
analogue input type
discrete input type
Programmable LI1...LI4 24 V 18...30 V
discrete input type
discrete input logic
Negative logic (sink), > 16 V (state 0), < 10 V (state 1), input impedance 3.5 kOhm
Positive logic (source), 0...< 5 V (state 0), > 11 V (state 1)
discrete input logic
sampling duration
20 ms, tolerance +/- 1 ms for logic input
10 ms for analogue input
sampling duration
linearity error
+/- 0.3 % of maximum value for analogue input
linearity error
analogue output type
AO1 software-configurable voltage: 0...10 V, impedance: 470 Ohm, resolution 8 bits
AO1 software-configurable current: 0...20 mA, impedance: 800 Ohm, resolution 8 bits
analogue output type
discrete output type
Logic output LO+, LO-
Protected relay output R1A, R1B, R1C 1 C/O
discrete output type
minimum switching current
5 mA at 24 V DC for logic relay
minimum switching current
maximum switching current
2 A 250 V AC inductive cos phi = 0.4 L/R = 7 ms logic relay
2 A 30 V DC inductive cos phi = 0.4 L/R = 7 ms logic relay
3 A 250 V AC resistive cos phi = 1 L/R = 0 ms logic relay
4 A 30 V DC resistive cos phi = 1 L/R = 0 ms logic relay
maximum switching current
braking to standstill
By DC injection, <30 s
braking to standstill
frequency resolution
Analog input: converter A/D, 10 bits
Display unit: 0.1 Hz
frequency resolution
time constant
20 ms +/- 1 ms for reference change
time constant
functionality
Basic
functionality
specific application
Commercial equipment
specific application
Variable speed drive application selection
Commercial equipment Mixer
Commercial equipment Other application
Textile Ironing
Variable speed drive application selection
motor starter type
Variable speed drive
motor starter type
discrete input number
4
discrete input number
discrete output number
2
discrete output number
analogue input number
1
analogue input number
analogue output number
1
analogue output number
asynchronous motor control profile
Sensorless flux vector control
Quadratic voltage/frequency ratio
Voltage/frequency ratio (V/f)
asynchronous motor control profile
transient overtorque
150…170 % of nominal motor torque depending on drive rating and type of motor
transient overtorque
acceleration and deceleration ramps
Linear from 0 to 999.9 s
U
S
acceleration and deceleration ramps
motor slip compensation
Adjustable
Preset in factory
motor slip compensation
switching frequency
2...16 kHz adjustable
4...16 kHz with derating factor
switching frequency
nominal switching frequency
4 kHz
nominal switching frequency
prospective line Isc
1 kA
prospective line Isc
protection type
Line supply overvoltage
Line supply undervoltage
Overcurrent between output phases and earth
Overheating protection
Short-circuit between motor phases
Against input phase loss in three-phase
Thermal motor protection via the drive by continuous calculation of I²t
protection type
quantity per set
Set of 1
quantity per set
width
105 mm
width
height
142 mm
height
depth
156.2 mm
depth
net weight
1.4 kg
net weight
electromagnetic emission
Radiated emissions environment 1 category C2 conforming to EN/IEC 61800-3 2...16 kHz shielded motor cable
Conducted emissions with integrated EMC filter environment 1 category C1 conforming to EN/IEC 61800-3 2, 4, 8, 12 and 16 kHz shielded motor cable <5 m
Conducted emissions with additional EMC filter environment 1 category C1 conforming to EN/IEC 61800-3 4...12 kHz shielded motor cable <20 m
Conducted emissions with additional EMC filter environment 1 category C2 conforming to EN/IEC 61800-3 4...12 kHz shielded motor cable <50 m
Conducted emissions with additional EMC filter environment 2 category C3 conforming to EN/IEC 61800-3 4...12 kHz shielded motor cable <50 m
Conducted emissions with integrated EMC filter environment 1 category C2 conforming to EN/IEC 61800-3 4...16 kHz shielded motor cable <5 m
Conducted emissions with integrated EMC filter environment 1 category C2 conforming to EN/IEC 61800-3 2, 4, 8, 12 and 16 kHz shielded motor cable <10 m
electromagnetic emission
vibration resistance
1 gn (f = 13…200 Hz) conforming to EN/IEC 60068-2-6
1.5 mm peak to peak (f = 3…13 Hz) - drive unmounted on symmetrical DIN rail - conforming to EN/IEC 60068-2-6
vibration resistance
shock resistance
15 gn conforming to EN/IEC 60068-2-27 for 11 ms
shock resistance
relative humidity
5…95 % without condensation conforming to IEC 60068-2-3
5…95 % without dripping water conforming to IEC 60068-2-3
relative humidity
ambient air temperature for operation
-10…50 °C protective cover from the top of the drive removed
50…60 °C with current derating 2.2 % per °C
ambient air temperature for operation
operating altitude
> 1000...2000 m with current derating 1 % per 100 m
<= 1000 m without derating
operating altitude
operating position
Vertical +/- 10 degree
operating position
product certifications
C-Tick
CSA
NOM
UL
GOST
product certifications
marking
CE
marking
assembly style
With heat sink
assembly style
electromagnetic compatibility
Electrical fast transient/burst immunity test level 4 conforming to EN/IEC 61000-4-4
Electrostatic discharge immunity test level 3 conforming to EN/IEC 61000-4-2
Immunity to conducted disturbances level 3 conforming to EN/IEC 61000-4-6
Radiated radio-frequency electromagnetic field immunity test level 3 conforming to EN/IEC 61000-4-3
Surge immunity test level 3 conforming to EN/IEC 61000-4-5
Voltage dips and interruptions immunity test conforming to EN/IEC 61000-4-11
electromagnetic compatibility
noise level
45 dB
noise level
ambient air temperature for storage
-25…70 °C
ambient air temperature for storage
Unit Type of Package 1
PCE
Unit Type of Package 1
Number of Units in Package 1
1
Number of Units in Package 1
Package 1 Weight
1.753 kg
Package 1 Weight
Package 1 Height
20 cm
Package 1 Height
Package 1 width
18 cm
Package 1 width
Package 1 Length
20 cm
Package 1 Length
Unit Type of Package 2
P06
Unit Type of Package 2
Number of Units in Package 2
30
Number of Units in Package 2
Package 2 Weight
65.95 kg
Package 2 Weight
Package 2 Height
73.5 cm
Package 2 Height
Package 2 width
60 cm
Package 2 width
Package 2 Length
80 cm
Package 2 Length
Package 3 Height
80 cm
Package 3 Height
Warranty
18 months
Warranty